Model No.Modèle nº45-0418CAUTION:Read Rules for Safe Operation and Instructions CarefullySafety•Assembly•Operation•Maintenance•Parts•ATV SNOW THR
10Lightly coat the top of the ring around the discharge 27. opening with general purpose grease.GREASE FIGURE 205/16" x 3"HEX BOLT5/16"
11Attach the chute tilt control to the control assembly 36. using (2) 5/16" x 1-3/4" carriage bolts, (2) bowed washers and (
12Slide the rear frame tube in or out of the push channel 42. to align it with the ATV hitch. Make sure the minimum 3"-4" clearance between
13OPERATIONKNOW YOUR SNOW THROWERRead this owner's manual and safety rules before operating your snow thrower.Compare the illustration below with
14REMOVING SNOW Snow removal conditions vary greatly from light uffy snowfall to wet heavy snow. Operating instructions must be exible to
15SERVICE AND ADJUSTMENTSSKID SHOE ADJUSTMENTThe skid shoes are mounted on each side of the spiral •auger housing. They regulate the distance the scr
16REMOVING THE BELT (Figures 32-35)Remove the key and disconnect the spark plug wire •from the snow thrower.Remove the engine pulley cover, the drive
17PARTS TO REMOVE AT END OF SEASONRemove the A-arm brackets from the suspension •of the ATV, especially before using your ATV for off-roadin
34SLOPE GUIDE(Keep this sheet in a safe place for future reference.)Use this guide to determine if a slope is safe for the operation of your ATV and s
364869525153535281928414141451626172693018212423141620282912292830329161116282945471716241423141613731434142424446164238163936333334211832353637434341
2This document (or manual) is protected under the U.S. Copyright Laws and the copyright laws of foreign countries, pursuant to the Universal Copyri
37REF QTY PART NO. DESCRIPTION 1 1 65683 50" Snow thrower Housing 2 1 71464 Drive Assembly 3 1 63768 Impeller 4 1 65685 Spiral Blades (LH) 5 1 65
3829193157574418717273444948445046546535320205353542053555341415220555342535452525253547453 4252544547512075512064719202020535343546966672084656462634
39REF QTY PART NO. DESCRIPTION 1 1 65699 Crank Rod Support 2 1 603-0302 Chute Tilt Bracket 3 1 684-0061 Crank Chute Assembly 4 2 784-5149 U-Joint Bloc
101516154565792151514513302820252381924263222951718271211201152121221522152282931REF QTY PART NO. DESCRIPTION 1 1 65688 Drive Control Plate 2 1 65689
3CARTON CONTENTSREF QTY DESCRIPTION 1 1 Snow thrower Housing 2 2 Housing Anchor Strap 3 1 Handlebar Switch 4 2 Stabilizer Bracket 5 1 Actuator 6 1 Out
4HARDWARE PACKAGEPARTS NOT SHOWNFULL SIZE1 23567242513171812201942122 2314151611292831891026273032
5ASSEMBLYREF QTY DESCRIPTION 1 3 Clevis Pin, 1/2" x 3-1/2" 2 1 Clevis Pin, 1/2" x 2" 3 4 Hex Bolt, 5/16-18 x 1" 4 4 Hex Bolt,
6Secure the relay pack near the battery of the ATV or 5. other location on the ATV out of harms way.Thread the 3 wire lead from the relay pack
7 FIGURE 94" Strut MountPolarisStrut Mount5-1/2"StrutMount6-5/8" StrutMount6-5/8" StrutMountBombardierOutlander StrutMount5/16&quo
8 FIGURE 14 FIGURE 13Attach the housing anchor straps to the 12. outside of the mounting tubes using (4) 1/2" x 2-1/4" hex bolts, (8) 1/2&q
9 FIGURE 18Attach the support bracket to the mounting tubes using 18. (4) 5/16" x 1-3/4" hex bolts, (8) 5/16" washers and (4) 5/16"
Kommentare zu diesen Handbüchern